• English
  • French

Scoopy+ S Last Firmware Update

Before proceeding with the update, please read carefully these
important instructions.

Firmware revision history (click a version for details)

Version 1.07.03

Released 2017/04/19          Click here to download the update file
Changes from previous version:

Improvements:

  • Improved handling of SIP call redirection.

Fixed issues :

  • If an incoming call is received while an AoIP session is running, call rejection with a "603 Decline" SIP code instead of "486 Busy Here". Issue on version 1.07.01, fixed.
Version 1.07.01

Version 1.07.01

Released 2017/02/02          
Changes from previous version:

New features :

  • Ability to select distinctive network quality settings for the Ethernet and the mobile IP interfaces.
  • Availability of LOAS encapsulation for AAC coding algorithms (for ISDN transmission), upgrading the interoperability with third-party codecs.

Improvements :

  • AoIP transmission statistics displayed on the "Connections" page of the html interface.
  • Ability to dial a number in the restricted access mode. From the default screen (bargraphs) one can dial and call a number. From the "Main" menu a pop-up message asks for the password granting full access to all the menus.
  • The Scoopy+ S now reboots right after a "Factory Reset" is performed.
  • AAC algorithms included in the codecs detected by the 5AS system.
  • More explicit error messages when an outgoing call fails.

Fixed issues :

  • Inaccurate overload indication on html page.
Version 1.06

Version 1.06

Released 2016/10/10          Click here to download the update file
Changes from previous version:

Fixed issues :

  • When recalling an ISDN call profile, the current coding algorithm was kept instead of recalling the one included in the profile.
  • ISDN line disturbed if another codec is connected on the same ISDN bus.
  • While recording, the elapsed time and remaining time counter would increase/decrease by steps of two seconds:  the increment is now one second.
  • Web interface, "Call Profiles" page: when clicking a profile in the list, the "Network" parameter was forced to "Ethernet". Fixed, the network recorded in the profile is recalled instead. 
Version 1.05

Version 1.05

Released 2016/08/29          
Changes from previous version:

New features :

  • Ability to customize the title of the tab in the html browser; this allows to identify easily a unit among a number of open pages on the browser.
    This new settings can be found in the "Misc" html page.
  • For mobile data, it is now possible to select between the "PAP" and "CHAP" authentication modes.

Improvements :

  • Improved the AoIP interoperability with third-party units that deal improperly with the channel number in SDP.
  • Improved AoIP interoperability for Opus coding, especially regarding the management of the stereo format and the bit rate.

Fixed issues :

  • Interoperability issue with codecs using the "MPA" payload type: fixed.
  • The device hangs if an ISDN link is set with AAC but with dissimilar configurations (different type AAC-LC or HE-AAC, or mono vs stereo): fixed.
  • Fixed various malfunctions in the handling of presets (create/update/load), in some cases imposing to reboot the unit.
  • Default route deleted from the routing table after editing the Ethernet parameters, leading to loss of control from a remote network: fixed.
Version 1.04

Version 1.04

Released 2016/04/18         
Changes from previous version:

New features :

  • Ability to setup an audio connection over an IP network without using the Session Initiation Protocol (SIP).  Please download this application note to see how to operate the codecs using the "Direct RTP" mode.
  • Ability to setup an audio connection over an IP network in Multicast mode.

Improvements :

  • Improved the stability of the AoIP controller for both Ethernet and wireless IP interfaces.
  • Display of the transmission quality on the root menu during IP communication for all algorithms (not only OPUS): 6-segment indicators showing respectively the quality of the transmission and the reception on the network.
  • Ability to display the "Relay status" in idle mode from the root menu when pressing the joystick to the right.
  • Web interface: added a title in the help section to remind the active tab. Front panel: show the “SIP User” parameter in the “About” menu.
  • Addition of two new audio routing modes for mono operation: “Standard” (default) or “Main & Backup”.
  • GPIO management: ability to manage two GPIO. This feature is available from the front panel (Tools/Misc/GPIO) or on the “Misc” page of the web interface.
  • GPIO extension: ability to manage four additional GPIO by using an extension USB relay box. This feature is available from the front panel (Tools/Misc/GPIO Extension) or on the “Misc” page of the web interface.

Fixed issues :

  • With very bad transmission quality, changing the bitrate of the Opus encoder on the fly, or using the “Relay transmission" feature, could release the call.
  • Under certain circumstances, an attempt to setup an audio over IP call with the packet replication option activated could lead to a failure to synchronize the audio.
  • Random sync losses with G722 SRT via ISDN lines emulated over an IP network.
Version 1.03

Version 1.03

Released 2015/12/22

New features :

  • Type of NAT displayed when STUN is active ("About" menu on front panel, "Status" page of html interface).
  • Ability to change the Opus bitrate during transmission, either via the front panel interface or the embedded html pages.
  • Transmission quality bargraph indicators displayed on the front panel
  • Support for the Thrane & Thrane Explorer 510 terminal (BGAN option)

Improvements :

  • For mobile IP data, improved handling of data connection issues (failure to establish a connection, unexpected data disconnection, connection retry process).
  • Increased resilience to IP packet losses for G711, G722 and MPEG L2.
  • "Remote" and "Local" profiles renamed, become "Call profiles" and "Presets".
  • Improved stability of the starting process when there is no IP network connectivity
  • Screen saver period reduced to 5 s.
  • On html page, parameters related to mobile data (data activation, APN, network quality..) are now accessible even if the current mobile mode is "Voice". 

Fixed issues :

  • Improper decoding of some SMS messages.
  • BGAN terminal detected but communication failure; communication over BGAN now fully operative.
  • Selection of IP or voice mode for mobile network in call profiles.
Version 1.02

Version 1.02

Released 2015/10/07
First release

< BACK